VIPER PRODUCTS > Spray-On Equipment | Accessories & Supplies | Chemicals
 
Glas-Craft Guardian A6-6000
The Glas-Craft Guardian A6-6000 Dispensing System is designed for economical use in small to medium polyurethane / polyurea output applications. The Guardian A6-6000 may also be used for higher output foam insulation, as well as pour foams. A 50-foot heated hose assembly is standard on the Guardian A6-6000 unit.

Specifications:
• Max Output: 20 lb per min / 9 kg per min
• Max Temp: 190º F / 88º C
• Primary Heaters: 6000 Watts
• Max Pressure: 2200/3000 PSI, 150/204 Bar
• Hose Size: 3/8” i.d. / 95 mm
• Length: 50 ft. Std / 310 Ft Max
• Heat: Copper-wound Hoses
• Heat Control: Solid-state LED Control
• Material Feed: Transfer Pumps
• P² Probler Gun: Round Spray 23950-01

Electrical Requirements:
Single Phase 220 VAC 50 amp 50 / 60 Hz
Three Phase 220 VAC 25 amp 50 / 60 Hz
Three Phase 380 VAC 25 amp 50 / 60 Hz

Air Requirements:
1 gpm/3.8 lpm output
33 cfm @ 100 psi 834 l / min @ 6.8 bar
Includes air transfer pumps
Glas-Craft Guardian A6-12000
The Glas-Craft Guardian A6-12000 Dispensing System is designed for use in house or in a field location. The Guardian A6-12000 is the most versatile unit for the money. It can be used for bedliners, industrial flooring, or various foam applications. A 50-foot heated hose assembly is standard on the Guardian A6-12000 unit.

Specifications:
• Max Output: 22 lb per min / 10 kg per min
• Max Temp: 190º F / 88º C
• Primary Heaters: 12000 Watts
• Max Pressure: 2200/3000 PSI, 150/204 Bar
• Hose Size: 3/8” i.d. / 95 mm
• Length: 50 ft. Std / 310 Ft Max
• Heat: Copper-wound Hoses
• Heat Control: Solid-state LED Control
• Material Feed: Transfer Pumps
• P² Probler Gun: Round Spray 23950-01

Electrical Requirements:
Single Phase 220 VAC 75 amp 50 / 60 Hz
Three Phase 220 VAC 35 amp 50 / 60 Hz
Three Phase 380 VAC 35 amp 50 / 60 Hz

Air Requirements:
1 gpm/3.8 lpm output
33 cfm @ 100 psi 834 l / min @ 6.8 bar
Includes air transfer pumps
Glas-Craft MH III
The Glas-Craft MH III Dispensing System is a hydraulically driven system, designed for use in house or in a field location. The MH III is the top of the line polyurethane/polyurea machine for the bedliner and is a lower air consumption unit. It relies on a hydraulic motor instead of a pneumatic motor. A 50-foot heated hose assembly is standard on the MH III unit.

Specifications:
• Max Output: 22 lb per min / 10 kg per min
• Max Temp: 190º F / 88º C
• Primary Heaters: 10000 Watts
• Max Pressure: 3000 PSI / 204 Bar
• Hose Size: 3/8” i.d. / 95 mm
• Length: 50 ft. Std / 310 Ft Max
• Length: 10 ft. Heated Whip
• Heat: Copper-wound Hoses
• Heat Control: Solid-state LED Control
• Material Feed: Transfer Pumps
• Probler Gun: Round Spray 17254-02

Electrical Requirements:
74 amp, 208-240 VAC, single phase, 60Hz.
50 amp, 208-240 VAC, three phase, 60Hz.
40 amp, 380 VAC, three phase 50/60 Hz.

Air Requirements:
15 cfm @100 psi / 425 l/min @ 6.8 bar

Probler 2 Gun

Probler 2 Gun Features:
• Lightweight, Ergonomic Design
Compact design makes it easy for operators to maneuver into difficult spray positions
• Hardened Metal Mixing Chamber & Side Block Seals
Longest lasting seals available 
• Two Piece Mixing Chamber
If a drill bit breaks off in the mixing chamber, you just replace the inexpensive snout - not the entire chamber
• Check Valve Separating Liquid Portion of Gun from Dry Areas
No more cleaning small air passages with tiny drill bits
• Dual Air Piston for Double the Triggering Force
Over 300 psi of trigger force - you will not see sluggish chamber movement when you pull the trigger
• Grease Fitting on the Gun for Daily Lubrication
You don't need to take the gun apart for daily service
• Individual Side Block Attachment to Gun
You will not need to line everything up or have a third hand to get side blocks attached to the gun
• Minimal Daily or Routine Maintenance Required
You don't need to take the gun apart daily - or even weekly
• The Probler 2 can be used with either harden steel or standard plastic side block seals.

Back To Top